RO-T (NO MASSAGE) 1. Instead of push buttons, the hand control had 2 large rocker switches. 2. The words “MODEL NO.: RO-T” are usually found written on the back above the FCC ID number. 3. In the battery compartment, tucked away in the upper right hand corner is a sliding switch labeled “CODE C-B-A”. Behind this label is a sliding switch. It is hard to see but it slides to select the A-B-C position. 4. The motors plug into a grey box (called the junction box or j-box) that is 3’ tall by 6 “ long by 6” wide. There is a green and yellow ground wire coming out of the box that is bolted to the frame. There is also a thin black antenna wire coming out of the box that is either stapled to the wood under the bed or just hangs there. On the side of the box is a sliding “A-B-C” switch that matches the one on the hand control. Both the hand control and the j-box must be set on the same frequency to operate the bed. R2-T, R2-T3 AND R2-T4 1. There are 13 push buttons - Head up, head down, foot up, foot down, massage timer on, and 1-2-3 speed buttons for the head massage, 1-2-3 speed buttons for the foot massage, head massage off and foot massage off. On the really old hand controls the buttons were colored and on the newer hand controls the buttons were fluorescent white. The buttons on the hand controls of the new system are also fluorescent white and this is what causes most of the confusion between the systems. 2. The words “MODEL NO.: R2-T or R2-T3 or R2-T4” are usually found written on the back above the FCC ID number. 3. In the battery compartment, tucked away in the upper left hand corner is a sliding switch labeled “CODE C-B-A”. Behind this label is a sliding switch. It is hard to see but it slides to select the A-B-C position. 4. The motors plug into a green box (called the junction box or j-box) that is 3’ tall by 6 “ long by 6” wide. There is a green and yellow ground wire coming out of the box that is bolted to the frame. There is also a thin black antenna wire coming out of the box that is either stapled to the wood under the bed or just hangs there. On the side of the box is a sliding “A-B-C” switch that matches the one on the hand control. Both the hand control and the j-box must be set on the same frequency to operate the bed.
MR2-T9 1. This is a long skinny hand control that is round on the bottom and flat on the top and has rounded sides. It operates via push buttons. The buttons were fluorescent white. 2. There is usually no model number written on it. In the battery compartment, tucked away in one of the corners is a sliding switch labeled “CODE C-B-A”. Behind this label is a sliding switch. It is hard to see but it slides to select the A-B-C position. it takes 3 triple A batteries 5. The motors plug into a green box (called the junction box or j-box) that is 3’ tall by 6 “ long by 6” wide. There is a green and yellow ground wire coming out of the box that is bolted to the frame. There is also a thin black antenna wire coming out of the box that is either stapled to the wood under the bed or just hangs there. On the side of the box is a sliding “A-B-C” switch that matches the one on the hand control. Both the hand control and the j-box must be set on the same frequency to operate the bed.
SEALY/CELEBRITY CHOICE 1. This is a long skinny hand control that is flat on the bottom and rounded on the top. It has flat sides and has a slight bend to it. It operates via push buttons. 2. There is usually no model number written on it. In the battery compartment, tucked away in one of the corners is a sliding switch labeled “CODE C-B-A”. Behind this label is a sliding switch. It is hard to see but it slides to select the A-B-C position. it takes a 9 volt batteries The motors plug into a yellow box (called the junction box or j-box) that is 3’ tall by 6 “ long by 6” wide. There is a green and yellow ground wire coming out of the box that is bolted to the frame. There is also a thin black antenna wire coming out of the box that is either stapled to the wood under the bed or just hangs there. On the side of the box is a sliding “A-B-C” switch that matches the one on the hand control. Both the hand control and the j-box must be set on the same frequency to operate the bed.
SIMMONS RPSP 1. This is a short flat grey hand control. A small door slides down to reveal both the massage buttons and some factory preset position buttons. It operates via push buttons. 2. There is usually no model number written on it. The battery compartment is located under the sliding door on the front of the hand control. In the battery compartment, tucked away in one of the corners is a sliding switch labeled “CODE C-B-A”. Behind this label is a sliding switch. It is hard to see but it slides to select the A-B-C position. It takes a 12 volt batteries. It looks like a AAA battery but is only half as long. The motors plug into a tan box (called the junction box or j-box) that is 3’ tall by 6 “ long by 6” wide. There is a green and yellow ground wire coming out of the box that is bolted to the frame. There is also a thin black antenna wire coming out of the box that is either stapled to the wood under the bed or just hangs there. On the side of the box is a sliding “A-B-C” switch that matches the one on the hand control. Both the hand control and the j-box must be set on the same frequency to operate the bed.
|