SERVICE
In addition to being the warranty center for Leggett & Platt, we can perform non-warranty repairs on almost all brands of adjustable beds.We can even convert most old hard wired hand controls into the new wireless remote hand control.
|
ACCESSORIES AND REPAIR PARTS
We have a large selection of accessories and repair parts for adjustable beds. If we don't have it and it is still being made, we can usually get it for you. Scroll down to see some of the standard accessories and repair parts that we have. If you don't see what you need, call us and we can get it for you!
Click here for accessories and repair parts quick list
|
HALF SIDE RAILS
We have half length side rails available for adjustable beds. The advantage of half length side rails is that they help keep you from falling out of bed yet they are out of the way when you want to get out of the bed. Most of our customers use them to hold onto getting out of bed. Two sets can be purchased if you need full length protection. They have a lovely chrome finish. They are easily installed by yourself or we can install them for you if you are in our service area.
| |
ALONE
|
INSTALLED
|
ONE
|
$ 135.00
|
$230.00
|
SET (2 PIECES)
|
$ 250.00
|
$345.00
|
|
 |
| HALF SIDE RAIL INSTALLED ON BED |
|
|
MATTRESS GUARDS
Mattress guards are the bar at the foot of the bed that keep your mattress from sliding off the foot of the bed when you raise the head of the bed. While the older mattress guards were flat black metal, the new ones are round chrome and are stronger that the old flat ones. They are available in two styles - one that bolts to the top of the base platform (usually for a Lifestyle™ or S-Cape™ base) and one that bolts to the bottom of the base platform (most all other beds). They are available in 17 inch and 30 inch widths. The 17 inch model can also be used on the side of the bed to keep light mattresses from sliding around when you get in and out of the bed.
$ 40.00 each
|
 |
| 30 INCH CHROME RETAINER BAR |
|
|
2-4-6 RISER KIT FOR L & P K-BASE
The 2-4-6 Riser Kit fits the Leggett and Platt K-bases (also know as InComfort™ bases)
They can be manually set to raise your bed 2 inches, 4 inches or 6 inches. Your original wheels push back into the bottom of them to retain your bed's mobility. One set is required for each bed so a dual king bed requires 2 sets. Each kit includes the required mounting hardware.
$ 110.00 per set
|
 |
| 2-4-6 RISER KIT FOR InComfort™ BASES |
|
|
LEGS FOR L & P LIFESTYLE™ BASES
The Leggett & Platt Lifestyle™ bases are equiped with interchangeable legs. They are available in 5 different sizes: 3 inch, 4 inch, 5 inch, 7 inch and 5 to 9 inch adjustable legs. The different size legs allow you to use a different thickness of mattresses on each side of a dual king and they allow you to adjust the height of your bed to make it easier to get in and out of the bed. The 5 to 9 inch adjustable legs have glides instead of wheels. The 3 inch legs are also available in chrome. You need one set per bed.
3", 4", 5", 7" LEGS $ 55.00 PER SET
5" to 9" ADJUSTABLE LEGS $ 70.00 PER SET
3" CHROME LEGS $ 60.00 PER SET
|
 |
| VARIOUS HEIGHT LEGS FOR L & P LIFESTYLE BASES |
|
|
ADJUSTA-MAGIC LEGS
We carry the full range of legs for the Adjusta-Magic bases from Leggett & Platt. They are available in 3", 4", 5", 6", 7", 8", 9", 10" and 11" lengths. A set of 4 is required for each bed.
$ 88.00 per set
|
HAND CONTROLS
We have both hard wired and remote hand controls.
Prices range from $ 85.00 to $ 150.00 depending on the model.
(note: the low voltage cord on the low voltage hand control is sold as a separate item - $20.00.)
|
 |
| L & P Remotes Click to enclarge. |
|
|
 |
| 110 VOLT HAND CONTROL. Click to enlarge. |
|
|
SLEEPER LOUNGE DRIVE BELTS
We carry the replacement drive belts for Sleeper Lounge bases. These belts should be replaced every 8 to 10 years before they break and strand you in an uncomfortable position. Changing a belt is like putting the chain back on a bicycle. You put the belt over the small pulley on the motor first and then roll it over the large pulley. The hardest part of changing these belts is getting under the bed to reach them. One size fits all.
SPECIAL NOTE:
These belts are getting harder and harder for us to procure. You may want to pick up a couple before they are no longer available!
$ 60.00 EACH
|
 |
| SLEEPER LOUNGE DRIVE BELT |
|
|
WIRELESS REMOTE CONTROL UPGRADE KITS
We can upgrade most hard wired hand control beds to the new remote controls. You have to replace both the hand control and the receiver under the beds.
$370.00 to $ 440.00 DEPENDING ON THE HAND CONTROL DESIRED
|
 |
| WIRELESS UPGRADE KITS |
|
|
MAXI-SAFE™ LIFT MOTOR FOR L & P K-BASE
The Maxi-Safe™ lift motor fits the Leggett and Platt K-bases (also know as InComfort™ bases). They have a built in safety switch that shuts the motor off it the bed encounters an obstruction on the way down. It is connected to the bed by an "Acme Nut" that is designed to break instead of the motor if excess weight is placed on the bed. No other motors have these features! The same motor works for the head or the foot of the bed.
$ 175.00 each
|
 |
| LEGGETT & PLATT MAXI-SAFE LIFT MOTOR |
|
|
ACME NUT
An "Acme Nut" that is designed to break instead of the motor if excess weight is placed on the bed. The acme nut at the foot of the bed has a "skirt" attached that causes the foot motor to shut off sooner than the head motor. This skirt rarely breaks and can be switched from the old acme nut to the new one. New beds have the black acme nut pictured here, older beds had a light blue acme nut. They are not interchangeable. We still have a few of the light blue acme nuts left.
$ 15.00 EACH
|
 |
| ACME NUT FOR LEGGETT & PLATT K-BASE |
|
|
LIFT MOTORS
We carry lift motors for most other brands of bed and the Leggett and Platt beds that don't use the Maxi-Safe motor. If you know what brand your base is, we may be able to get you an exact match, otherwise we have a generic motor that you can use. The plug on the end of the power cord is different for each manufacturer. You may have to splice the plug from the old motor onto the new motor or we can do it for you.
$ 175.00
|
 |
| GENERIC LIFT MOTOR |
|
|
OKI WHISPER MOTORS
Many of the newer beds now use Oki Whisper Motors. Not only are they whisper quiet, they have the option of having a battery backup in case of a power failure.
$ 350.00
|
 |
| OKI WHISPER MOTOR |
|
|
REPLACEMENT WHEELS
We carry replacement locking wheels for most beds. We have both the push in wheels and screw in wheels. The screw in wheels are for use on Lifestyle™ bases when the legs are removed. We also carry the push in or screw in glides.
PUSH IN WHEELS $ 7.50 EACH / $ 30.00 SET OF 4
SCREW IN WHEELS $ $ 10.50 EACH / $ 42.00 SET OF 4
PUSH IN GLIDES $ 30.00 SET OF 4 ONLY
SCREW IN GLIDES $ 34.00 SET OF 4 ONLY
|
 |
| VARIOUS REPLACEMENT WHEELS |
|
|
RUBBER CASTER CUPS
Adjustable beds stay in place quite well on carpet. On tile or hardwood floors its another story though, even with locking caster. That's because the casters are made of plastic, not rubber. These rubber cups are made just for adjustable beds. They are deep enough that the bed won't roll out of them and they don't slide at all when they have weight on them. The only disadvantage is that they make it hare to pull the beds apart when you are changing the fitted bottom sheets on the dual king sets. There are 4 cups in a set and each bed takes a set.
$35.00 for a set of 4
|
 |
| Rubber Caster Cups |
|
|
HEADBOARD/FOOTBOARD BRACKETS
We carry all of the head and foot board brackets for Leggett & Platt bases. We also have the swing away brackets for attaching dual king beds to headboards.
$ 40.00 TO $ 70.00 DEPENDING ON THE MODEL
SWING AWAY BRACKETS $ 25.00
ADAPTER PLATES $ 20.00
|
|